It is true that automatic garage doors are very practical. However, it is inevitable that from time to time the odd problem will arise. That is why in this article we want to talk to you about the most frequent faults in automatic Garage Door Service in Sydney, so that you can recognize the problem and solve it.
Garage door mechanisms typically offer a high degree of reliability. In fact, more and more effort is being put into making quality and durable products.
However, there are certain factors that will necessarily affect the garage door, such as continued use or weather conditions.
Frequent faults in automatic garage doors
Sometimes the door does not work, but it is difficult to find out the reason for the failure. That is why we want to explain to you what the most frequent breakdowns or failures in automatic garage doors are.
Garage door won’t open
It is one of the most typical breakdowns and, specifically, there are two very common reasons:
A problem with the control that operates the door. Oddly enough, sometimes the explanation is as simple as that the remote has run out of batteries. Check that, in fact, the remote has a battery. If it’s charged and still doesn’t work, it may be faulty. In this case, the most advisable thing is that you contact a professional to verify that it does not work, and repair it with all the guarantees.
A failure of the signal receiving device . As with the controller, only an expert can carry out the repair. However, there is a possibility that it is not damaged and that it is an interference that prevents the waves from reaching it. Most garage remotes have a control box. To check if the problem is interference you can use the input button in this box.
You should also check that the electronic board of the motor is turned on. If so, check that the source of the problem is not any of the accessories, such as the photocells. Disconnect them one by one to discard them.
If the electronic board is off, check the condition of its fuses.
Another cause can be a loose cable or a bad connection . This type of breakdown can be caused by the vibrations of the engine itself. This is why it is important that, at the time of installation, all the wiring is hidden and safe.
In any case, before checking the wiring, take precautions and cut off the current. You must follow the following steps:
- Check the entire installation.
- If the problem is a terminal that has become loose, it is as simple as retightening it.
- On the other hand, if there is a broken or disconnected cable, it will be necessary to make a splice or replace what has been damaged.
It is possible that you do not have the necessary notions to carry out this work. If you have any doubts , contact a professional , since these installations are delicate and it can be dangerous to manipulate them if you do not have experience.
Garage door won’t open or close
This situation may be due to a fault in the control or in the receiving device, but there may also be a problem with the mechanism that moves the door. Most likely it is clogged.
It is essential that you do not try to force the door, as it could worsen the problem you are trying to solve.
The most correct way to act is to carry out proper maintenance, and clean the guides and rails from the first moment you notice that the door does not slide as well as it should. In many cases these problems are aggravated because they are not solved in time.
In the most serious traffic jams, it is necessary to disassemble the garage door in order to remove the obstacle that is obstructing it. Here are some tips to do it on your own:
- Always keep a certain order to disassemble and reassemble the door. You can write everything down to make sure you don’t forget the steps you are following.
- Store small pieces in a closed container so you don’t lose any.
- You can take advantage to lubricate the parts if you want to get a smoother bearing.
On the other hand, maybe you need to repair your garage door because it won’t open or close all the way. The first thing is to check the established maneuver times, and the limit switches can also be checked.
Again, our advice is to contact a professional if you are not completely sure that you can carry out the task on your own.
Taking the risk without having the necessary skills can end up with an even worse breakdown or even an accident, so it is not recommended at all.
Garage door opens properly but won’t close
The cause of this problem may be in the photocell or in any other safety element. In fact, the function of the security elements is to guarantee that the door can be closed without danger. That is why it is usual for the door to open without problems, but not to close afterwards.
The first step is to identify which accessory is causing the problem. Next it is necessary to check that the door works well without said accessory. If so, it will have to be replaced with a new one.
Garage door makes strange noises
Sometimes we do not pay enough attention to the maintenance of the Automatic Gates Brisbane, and we do not bother to grease its mechanisms. This can result in rattling and grinding noises from moving parts.
Knocking or rattling can also occur if a gear has been displaced from where it should be.
Your installer may have instructed you on how to grease the parts, in which case you can try this to see if the noises stop. Otherwise you should not touch anything so as not to aggravate the problem; The best solution will be to call a professional.
The door motor sounds, but the door does not move or moves very slowly
This is a very common problem with sliding garage doors. Most of the time the problem is that the capacitor has deteriorated and is not capable of giving the necessary impulse to the motor. In this case, you will have to replace the condenser.
On the other hand, there may be a situation that the door is too hard. In this sense, it is convenient that, first of all, you move the door manually to check that it slides smoothly and that there are no obstacles.
The door moves a little, stops and goes back
It is another typical failure of sliding doors. One possible explanation is that the engine’s anti-crush system is sensing some small obstruction and thinks it’s hitting someone. Another possibility is that this system is faulty.
In any case, these are just some of the many possible explanations for a garage door failure.
We hope we have helped you but, if not, do not hesitate to contact a professional so that they can advise you and solve your problem.